Explore our library of published papers, journal articles, and white papers referencing our software.
In this interview from The Mobile Network, Remcom discusses how a new approach to Massive MIMO channel modeling will be key to success of 5G network rollouts and applications.
This presentation demonstrates a new predictive capability for simulating massive MIMO antennas and beamforming in dense urban propagation environments. Remcom's unique approach allows us to predict the signal-to-interference-plus-noise ratio (SINR) at specific device locations and the actual physical beams formed using these techniques, including unintentional distortions caused by pilot contamination.
To keep up with rising demand and new technologies, the wireless industry is researching a wide array of solutions for 5G, including Massive MIMO. Remcom’s Wireless InSite provides an efficient method to predict channel characteristics for large-array MIMO antennas in complex multipath environments.
Full wave matching circuit optimization (FW-MCO) is a new technology that combines full wave, 3D EM simulation with circuit optimization into a novel approach for solving an age-old RF problem: determining which component values provide the desired match for a given matching network layout. This article describes the design process using the design of a matching circuit for a GPS-Bluetooth antenna.
This paper, featured in the July 2015 issue of Microwave Journal, provides a technical comparison of 3D planar EM simulation with fully arbitrary 3D EM simulation and informs users as to which EM approach/formulation may work best for a given application.
XF’s Circuit Element Optimizer utilizes full wave analysis to select the component values for a given printed circuit board (PCB) layout. The tool allows design engineers to optimize matching circuit lumped element values directly in the EM layout where the coupling from multiple antennas and the ground return current paths are taken into account. This whitepaper gives an overview of how the Circuit Element Optimizer works and the benefits it provides.
Electromagnetic simulation has been used by RF engineers for many years to aid the design of automotive radar sensors, but the increasing demands of advanced driver assistance systems (ADAS) are changing the methods used. This paper introduces FDTD’s advantages for automotive radar circuit and systems level designers, including simulation of very large problems, more efficient memory requirements, and the ability to reveal sources of coupling.
This whitepaper demonstrates how XFdtd's time-domain approach enables rapid development by allowing engineers to determine the performance of a fully detailed sensor model installed behind a piece of fascia without needing to build prototypes and run tests in an anechoic chamber. The analysis of a 25 GHz sensor frames the discussion.
Advances in computing resources have made it possible to quickly and accurately model the anti-reflective properties of 3-dimensional sub-wavelength structures. In this paper, the FDTD method was used to model anti-reflective properties of a variety of sub-wavelength structures for 300 to 1300 nm input light.
In this paper, FDTD simulations are performed on a 900 MHz band antenna inside and outside the carbon fiber body of a solar-powered electric vehicle. Data are analyzed to determine the optimal antenna placement for transmission to a receiving antenna located toward the rear of the solar vehicle.
This presentation demonstrates how the 3D ray tracing code in Wireless InSite can accurately predict received power coverage even in a multi-room environment containing many walls and different materials types. In order to verify the accuracy of the code, the floor plan of Remcom’s business offices was modeled in the software with a WiFi antenna and a third party tool was used to create a coverage plot of the received power throughout several of the suites.
Remcom's XFdtd software is well-suited for any microwave device design or analysis task. Our Waveguide Examples booklet showcases a collection of five different waveguide applications with downloadable project files.
This paper outlines the advantages of FDTD EM simulation for analyzing antenna-in-system designs that include both the antenna package and the automobile body features surrounding the device. An XFdtd simulation of a radar mounted in the rear bumper of a sedan provides the framework for the discussion.
With XFdtd, there is no limit to the resources you can exploit to solve your EM calculations. This report quantifies the performance profile of XF's GPU and MPI technologies. We demonstrate the pros and cons of different combinations of equipment and techniques, including cost considerations for those researching available hardware.
This presentation describes the simulation of a hearing instrument (HI) device. The design was simulated in the presence of a homogeneous SAM phantom and an anatomically correct, heterogeneous head model. The simulation results illustrate the differences between the head models and highlight the more acceptable results for improved device safety.
This study considers the example of designing a broadband antenna for an unattended ground sensor using XFdtd. To address the challenge of attaining acceptable performance over both dry and wet ground conditions, we use Particle Swarm Optimization (PSO). XStream GPU Acceleration and MPI + GPU technology make this type of sophisticated simulation strategy possible, completing multiple optimizations with hundreds of generations to converge on the best values.
An effective approach is presented for simulation of thin resistive sheets in FDTD. The approach is based on surface impedance and piecewise linear recursive convolution technique. This approach can be combined with a conformal scheme so that it can be applied to deal with an arbitrarily shaped thin sheet. The simulation results for a couple of examples have shown that the approach is robust, stable and quite accurate.
Uncertainty in structure geometry is a fundamental limitation of ray-tracing methods when simulating urban propagation. We present a hybrid approach using ray-tracing methods and empirically derived loss factors to incorporate the effect of unknown interior layouts. This approach is compared with a more typical empirical implementation to demonstrate the benefits of hybridization.
Heterogeneous, mobile wireless networks are becoming increasingly difficult to validate for operational use. Presented is an approach to reduce the run-time of these high fidelity simulations by constructing precise results based on adjacent ray-paths from a lower resolution simulation. Speed and accuracy trade-offs are presented for this approach in typical urban scenarios, demonstrating its effectiveness in meeting the growing needs of wireless channel emulation.
A fast approach is proposed for estimating the thermal responses of biological bodies due to RF exposures. The approach is based on ANN models. The results obtained from the fast approach agree well with those calculated directly from the thermal solver. The advantage is that the approach is fast and is not dependent on the biological body and mesh sizes.
Accurately characterizing the propagation of RF signals in tunnels is important for rescue, safety, and military purposes. The material composition of the tunnel, the tunnel shape and size, obstructions, and tunnel bends present challenges. In this paper we use Wireless InSite to analyze how tunnel diameter and shape affect the propagation characteristics.
This paper presents results from modeling RF propagation in a mine using Wireless InSite's Uniform Theory of Diffraction (UTD) ray tracing code to portray a communications system within a mine environment.
This paper presents results from sea to land propagation using Wireless InSite. The effort explores the effects of various elements in the scene and how they impact the results. The various elements in the scene include the ships out at sea, the ships docked, the docks themselves, the buildings around the dock area, and the material properties of each.
Wind turbines located near a radar installation can significantly interfere with the ability of the radar to operate properly. Remcom has performed a number of research efforts into the impact that wind turbines and wind farms have on radar returns for Air Traffic Control (ATC) radar, early warning radar, weather radar, and instrumentation radar. Highlights of some of these effects and relevant samples and white papers are provided in this brief overview.
Radar scattering from a turbine’s moving blades can interfere with Doppler radar systems, producing ghost images. Understanding the scattering properties of a blade helps to mitigate any potential issues. This study compares the radar cross section of a metal turbine blade, a hollow fiberglass turbine blade, and a hollow fiberglass turbine blade with a metal spar using XFdtd.
The use of general purpose computing on a GPU is an effective way to accelerate the FDTD method. This paper introduces ﬂexibility to the theoretically best available approach and examines the performance on both Tesla and Fermi architecture GPUs and identiﬁes the best way to determine the GPU parameters for the proposed method.
This application note from the January 2013 issue of Microwave Journal demonstrates the process of adding an electrically steerable, conformal antenna array to the body of a high speed missile. By leveraging XF’s XStream GPU Acceleration, a complex 3D simulation including multiple array elements with curved surfaces that could take several hours was completed within a few minutes.
This paper discusses using GPU acceleration within the Moving Window Finite Difference Time Domain (MWFDTD) method to achieve real time propagation simulation while maintaining accuracy.
In this paper, a conformal 2D FDFD Eigen mode method is derived for solving arbitrarily shaped waveguides or transmission lines. Some examples such as horn antennas, circular waveguide filters and differential pairs are presented to show the capabilities of the developed conformal 2D FDFD Eigen mode solver.
This paper demonstrates the design of Rotman lens for ESM sensor application in operation band 32-38 GHz. The initial design is created in Remcom’s Rotman Lens Designer and then verified against experimental measurements. Parameters of the realized prototype are presented and methods of increasing its performance are outlined.
Ready to evaluate Remcom's EM Simulation Solutions?